In recent years, the home improvement market has been mixed and the decoration has been “seeing flowers in the fog.†It will fall into the decoration trap if it is inattentive. At the end of the entire home improvement, acceptance and closing are required. Acceptance and closing are the last critical points in the home improvement process. So what are the standards for home decoration acceptance ? Next Xiaobian will give you a detailed introduction.
Acceptance Criteria for Home Improvement Construction 1. Acceptance criteria for suspended ceilings: The types, specifications, and colors of the materials used for the suspended ceilings should be consistent with the requirements of the design specifications; the cover panels and the keel should be tightly connected, and the surface should be flat and free of contamination. Cracks, missing corners, hammers and other defects, joints should be uniform, paste the cover panel must not have delamination, plywood shall not be through the place; Shelving cover panel shall not have leakage, penetration, angle phenomenon.
Acceptance standards for home improvement construction II. Acceptance criteria for electrical engineering: The leakage switch is installed correctly and is used normally; the installation and fixing of electrical devices and equipment should be firm and smooth; the electrical power-on test, lighting test and lamp control performance are good; switch, socket, terminal box The appearance of the device is good, the insulation device is crack-free, the installation is firm and flat, the installation method is in compliance with the regulations, the deviation of the switch and socket terminal box installed side by side, the clearance of the panel, the box surrounding the concealed switch, socket, terminal box is in compliance; The power of the system is complete, and it meets the requirements for use. The appliance is firmly installed and is flat.
Acceptance Criteria for Home Improvement Construction III. Acceptance Criteria for Paper Pasting Project: After the paper paste is completed and dried, it can be accepted; when it is accepted, check whether the material type, color and pattern meet the design requirements; the wallpaper and wall cloth must be firmly bonded and the surface color is consistent. No air bubbles, empty drums, cracks, wrinkles and stains. No scotch marks on strabismus; smooth surface, no corrugations, wallpaper, wall coverings and hanging mirrors, vertices, face plates, skirting boards, wainscoting Batten, curtain hanging box next to, 1.5 meters away, visual inspection shall not have obvious gaps; all stitching horizontal and vertical, stitching pattern, pattern fit, do not leave the seam, not overlapping; yin and yang vertical angle, angular, the corner Shun shun light, no seams at the corner; wallpaper, wall cloth edge straight and tidy, no paper hair, flying thorn; no leakage stickers, subsidies and delamination.
Acceptance Criteria for Home Improvement Construction IV. Acceptance Criteria for Flower Ornamental Works: The floral ornament project can only be accepted after it is completed and dried. Acceptance of the floral ornament project should check whether the variety, specification, and design of the floral ornament meet the design requirements; the floral ornament should be installed firmly, its quality requirements and allowable Deviation should be in accordance with: the horizontal and vertical allowable deviation of strip floral decoration, no more than every meter, the total length shall not exceed 3 mm; the allowable deviation of the position of individual floral ornaments shall not be greater than 10 mm; the surface of the floral ornament shall be smooth, with clear patterns and tight joints There must be no defects such as cracks, warpage, missing corners, etc.; the surface of the silk flower should be smooth, with clear patterns and no cracks.
Acceptance criteria for home improvement construction 5. Acceptance criteria for water supply and drainage pipeline installation engineering: The quality of pipelines and pipe fittings should comply with the current standards; the installation of valves should be correct and the switches should be flexible; with water pressure testing, all pipelines, valves, and joints should be free from water seepage and water leakage. phenomenon.
Acceptance standards for home improvement construction VI. Acceptance standards for wooden floor installations: The materials should meet the requirements of households and the current product standards; floor installation (bonding) should be solid, no noise, no looseness; wooden floor surface should be polished flat, no planing marks , slags and burrs and other phenomena, varnish the floor of the pattern (grain) should be clear; parquet floor seams should be aligned, the gap width is consistent, the surface is clean, no plastic spill phenomenon; skirting board and the floor is closely connected; skirting board along the flat Straight, full height difference should be no more than ± 3 mm close to the wall, seamless.
Acceptance criteria for home improvement construction 7. Acceptance criteria for construction quality of plastic board surface: The material, color, and paving should meet the requirements of tenants; the surface should be smooth, smooth, wrinkle-free, and must not be curled or bubbling; the color must be the same, the joints must be tight, and the four sides should be smooth. Straight, degumming site shall not be greater than 20 mm, and the spacing between them shall not be less than 500 mm; the joint with the pipeline shall be tight, firm and flat; the skirting board shall be closely connected with the plastic plate; the skirt plate shall be straight and the full-length elevation shall not be greater than ±3 mm. , close to the wall, seamless.
Home Construction Acceptance Criterion VIII. Acceptance Standards for Construction Quality of Plate Surfaces: Materials and patterns conform to the requirements of households, product quality conforms to national standards and technical regulations; paving should be firm, not loose, and the ground level elevation should not exceed 0.5 mm; paving patterns should be clear , No stain, pulp marks; Straight seams, pull seam inspection, deviation is not greater than 2 mm; seam width is not greater than 1.0 mm; seam height difference between the block and block is not greater than 0.5 mm.
Home decoration construction acceptance standards Nine, carpet installation quality acceptance standards: solid carpet, flat carpet surface, can not afford to drum, not sag, no Alice, no wrinkle; patchwork joints should be glued or seamed, compact formation, Does not reveal the patchwork, the suede hair along the light is the same, the edge is reasonable, the surface is clean, no oil; paste paste the carpet and the ground fixed, smooth. The card-type fixed hand carpet and the barbed plate are firmly embedded; the overall color and gloss are the same, the pattern is pulled correctly, and there is no wrong flower or lattice phenomenon; the intersection of the carpet and other floors and the closing mouth should be straight, and the closing layer can be used. And the transfer of pressure layer compaction, the entrance with the bold to be compacted, skirting the plug tight, smooth sealing.
Acceptance criteria for home improvement construction Ten. Acceptance of fine wood products: Fine wood products for home decoration generally include curtain boxes, heating covers, skirting boards, door and door covers, wooden wall skirtings, wall cabinets, and closets. Qualified decoration, fine wood products and grass-roots products must be studded firmly, no loose phenomenon. The ash plywood plywood can not be used alone, it must be fixed on the plywood, wood core board and other layers, and fixed with glue guns. Curtain boxes, door covers, etc., require that the surface be flat and do not bend and deform. Solid wood edging the door plywood to diagonally spliced, there is no obvious color, cracks, wood decorative lines to be consistent, structured, coordinated, no color, cracks, uniform thickness, can not use particleboard, because of its moisture easily deformed, use The ash plywood plywood should be more than Class A, and should be planed at the plane splicing, and the pattern color should be similar.
Editor's summary: The ten home improvement acceptance criteria are introduced here. For more information, you can follow this site information.
Water and Electricity Acceptance Construction Acceptance Paint Construction Acceptance Home Improvement Home Improvement Size Data
Right Side Roller Shutter Lock,Solid brass cylinder with full brass teeth key or computer key.
- Single turn, 3 pins Cylinder Lock
- Right sided straight , shifted, Lengthened bolt available with 6mm hole
- Interchangeable: With most common roller shutter locks available on the market. The reinforced bolt makes the roller shutter more resistant to attack.
- Available for motorized roller shutter
- Reinforced steel bolt: 2mm steel plated folded back on itself to reach overall 6.5mm thickness
- Rustproof zinc plated box and components
Right Side Roller Shutter Lock
Right Side Roller Shutter Lock,Half Lock Cylinder,Roller Shutter European Door Lock ,Interior Roller Shutter Door Lock
Rayma(SJZ) International Trading Co., Ltd. , https://www.raymalock.com