HC Security Network News With the rapid development of smart home, intelligent lock as an important part gradually accepted by the people, but also to lock bid farewell to the cold image of "Iron General", gives more room for imagination and interaction. The most important thing is that today's smart locks have replaced the mechanical locks.
However, there are more people, and various problems will come. Therefore, Xiaobian is here today to sort out some of the problems and solutions that God may encounter when using smart locks~~Hurry up to get these small points, so that you can use smart locks in your daily life and play as soon as possible. Turn your home smart lock!
1. No reaction after installation
1. Confirm that the battery with sufficient power and the positive and negative terminals are correct.
2. Remove the rear panel and check if the wires are connected or tightly connected.
3. Remove the lock body and check if the lock body wire is squeezed and rearrange the wires.
2, the lock is dead! !
Smart locks have voice prompts if the battery is low. Therefore, it is necessary to replace the battery in time~ The smart lock is used for half a year to about 1 year. It is best to open the battery cover to check the battery to prevent the battery from invading the fingerprint lock circuit board (especially during the rainy season, humid air will be used for any home appliances). There are hidden dangers, please check and maintain in time, use the home appliances correctly, and find that the battery has oxidation phenomenon, please replace the new good quality battery!
3, the smart lock has been used for a long time, the surface is bleak
Never let the lock surface come into contact with corrosive substances, which will damage the lock surface protective layer, affect the gloss of the lock surface or cause oxidation of the surface coating. Imagine applying a chili noodle on your face. Is there a feeling of faint sorrow?
4, fingerprint verification is successful but can not unlock
1. Two important components in the fingerprint lock: one is the fingerprint module and the other is the electronic clutch. When the verification is successful, carefully listen to the sound of the motor rotating in the lock. If there is no motor rotation, the circuit from the board to the motor may be broken. Some motors have a rotating sound, and the square bar inside the handle may have fallen off. At this time, it is best to contact and sell later!
2, the door is skewed, causing the tongue and the gusset to rub too much, can not open the door
5, touch the sensor keyboard, the screen does not respond
1. Check the battery box to ensure that the battery is fully charged and the positive and negative poles are installed correctly.
2. Whether the working mode is the fingerprint mode (the touch button does not respond in the fingerprint mode).
6, I feel that fingerprint reading is a bit slow
After installing the smart lock, you must try it wildly and repeatedly, and confirm that there is no problem before you can install the master. If the reaction is slow after installation for a period of time, consider using the fingerprint collection window for a long time. The surface will be stained with dirt or the surface is wet. Wipe gently with a dry soft cloth. Note that it is a dry soft cloth~ Iron shavings are not suitable...
7, can not delete fingerprints or change passwords
Confirm whether the current fingerprint is the administrative user fingerprint. If not, you cannot change the fingerprint overpass password. To manage your fingerprint or change your password, follow the correct steps.
8, the smart lock handle is not smooth
1. The panel mounting leads to excessive friction between the lock body and the panel. Please adjust the panel position.
2. After the fingerprint matching is successful, the handle is not turned over for a long time. Please re-enter your fingerprint to open the door.
9, the display prompt has been locked
This is a situation that occurs when multiple fingerprints or passwords are entered incorrectly. Generally, waiting for 3-5 minutes, the smart lock will be automatically unlocked, and no operation can be performed on the display during the lock. This is the anti-theft settings of the system, don't try to open it through violence~
10. Is there a problem with the security door, affecting the smart lock?
If the door is deformed or the door frame is drooping, the combined oblique tongue will enter the door frame box and the friction will be too large. It should not be fully extended. At this time, the position of the door plate should be adjusted. Otherwise, the smart lock will follow the deformation and then there will be problems!
Editor in charge: Zhang Zequn
Fan Light,Ceiling Fan Light,Led Ceiling Lamp Light,Led Ceiling Fan
JIANGMEN MOSCOT OPTOELECTRONIC TECHNOLOGY CO.,LTD. , https://www.zjsensorsled.com