The five directions of tile design this spring

Plastic composite steel plate

It is a soft or semi-rigid polyvinyl chloride plastic film covered with 0.2 to 0.4 mm on steel plate or pressed steel plate, divided into two kinds of single-sided and double-sided coating. It has the characteristics of insulation, wear resistance, corrosion resistance, oil resistance, etc. It can be used for wall panels and roof panels.

Decorative panels

It is made of natural wood sliced ​​or peeled into thin slices 0.2 to 1 mm thick, and then glued to a plywood, fiberboard, particleboard, and other substrates. This material has a clear texture and natural color and is a higher-grade decorative material.

Calcium plastic board

It is based on high-pressure polyethylene as a base material, adding a lot of light calcium carbonate and a small amount of additives, after plasticizing, hot pressing, foaming and other processes. This plate is lightweight, soundproof, heat-insulating and moisture-proof. Mainly used for ceiling surface materials.

Medium density fiberboard

Density fiberboard is a kind of man-made board. It uses plant fibers as raw materials, and is cut into pieces, separated into fibers, formed into slabs (mixed with resin glue and additive paving), under heat and pressure, cellulose and hemicellulose and A sheet of lignin plasticized.

Fibreboard

According to the bulk density, it can be divided into hard fiberboard, semi-hard fiberboard and soft fiberboard. Hard fiberboard is mainly used for the panel of the ceiling and partition wall. The board surface is drilled to form various patterns. The surface is sprayed with various paints, and the decorative effect is better. Hard fiberboard sound absorption, waterproof performance, durable, easy construction.

Yellow Pineapple Wood

The wood is glossy, the annual rings are clear and uniform, the material is soft, easy to dry, and processed. The material color and pattern are very beautiful. It has good paint and cementation properties, is not easy to crack, and has good corrosion resistance. It is a material for high-grade furniture.

Tochigi

Aroma, anti-corrosion, pest control, slightly lighter material, not easily deformed, easy processing, smooth cut surface, beautiful color after painting.

Tochigi

Hard texture, large specific gravity, high strength, and dense structure. It is resistant to moisture, abrasion, and is not easy to be cemented. It has good coloring properties, rough texture, and relatively thick tracheids. It has obvious wooden rays and is not easy to dry. Generally, it can be made of wood flooring or furniture.

Ash

Material is slightly hard, beautiful pattern, corrosion resistance, water resistance, easy processing, high toughness, cemented paint, good coloring performance, good decorative performance, is a kind of wood used in the current decorative materials.

Melamine board

The full name is melamine impregnated film coated wood-based panels. The paper is made of melamine resin adhesive soaked in paper with different colors or textures, and then dried to a certain degree of curing, and it is paved on the surface of particleboard, medium-density fiberboard or hardboard, and the hot-pressed decorative board.

PE calcium plastic board

The main raw materials of calcium plastic board are resin, filler and foaming agent. It is a raw material plastic mixing machine to uniformly press out the sheet material in the mold expander to expand the heat to open the mold, the sheet material immediately expanded into calcium plastic foam board. The expansion of the expansion of the long-expansion 1.7 times the thickness of the expansion of 2 times.

Aluminum composite panel

It is based on high-pressure polyethylene as the substrate, adding a large amount of aluminum hydroxide and a suitable amount of flame retardant, plasticizing, hot pressing, foaming and other processes. This plate is lightweight, soundproof, heat-insulating and moisture-proof. Mainly used for ceiling and wall surface materials.

Plywood (plywood)

The plywood is a three- or multi-layer plate-like material obtained by peeling a veneer into a veneer or a wood veneer, and then bonding it with an adhesive. Three or more layers of plate-shaped material are generally used, and odd-numbered veneers are generally used, and adjacent veneers are formed. The fiber direction is perpendicular to each other and the front and the inner plates are arranged symmetrically on both sides of the center layer or the core.

Slim wood plywood

The ash, willow, wood, birch, etc. are cut into thin slices of 0.1-0.5mm thickness, and plywood is used as the base material. The pattern is beautiful and the decoration is good.

Liu Anmu

The material is moderate in weight, slightly thick in structure, easy to process, has good cementation performance, and slightly warped and cracked in the drying process. It is mostly used for making plywood or penta-plywood.

Chinese fir

The material is light and light, easy to dry, easy to process, rough cut surface, medium strength, easy to split, good adhesive performance, is currently used mid-range wood.

Tochigi

Glossy wood, slightly thick structure, slow drying speed, not easy to warp, easy to process, strong nails.

Basswood

The material is soft, grease, abrasion resistance, corrosion resistance, not easy to crack, fine grain, easy processing, strong toughness. The scope of application is relatively wide, and it can be used to make decorative materials such as wood lines, blockboards, and wood crafts.

Redwood

Hard material, not easy to process, not easy to dry, strong nail holding power, good cementation and paint performance. Suitable for decorative plates and high-grade furniture.

Bagasse chipboard

Sugarcane bagasse is the residue after sugar refining. The sugarcane bagasse with the same chemical composition as wood is a very good raw material for making plates. Due to the small proportion of bagasse, the fiber quality is good, the prepared plate has high strength and light weight. Low water swelling rate. It is a medium-density chipboard with smooth surface, beautiful color, good dimensional stability, good mechanical processing performance and decorative performance. Uses: Suitable for furniture, construction, carriages, ships, packing boxes and other production industries.

Gradual structure particle board

From the surface of the chipboard to the center, the shavings gradually changed from small to large, and there was no noticeable change in the core layer. The air-laid paving machine was used. Smooth and smooth surface, high strength, good dimensional stability, good mechanical processing and surface decoration.

Directional Particleboard (OSB)

Oriented structure particle board is a kind of flake with 40mm, 70mm, width 5mm, 20mm, thickness 0.3mm, 0.7mm, and processed by special equipment with small diameter material, thinning material, wood core, board skin, branch material, etc. as raw materials. , sizing and special equipment A core-slab splicing plate is crisscrossed and oriented, and after being heat-pressed to form a man-made board. Because OSB uses a special process and many special equipment, it has the advantages of high bending strength, small linear expansion coefficient, good dimensional stability, strong nail holding force, easy surface decoration, etc. It is widely used in packaging, construction and vehicles. Shipbuilding and other industries.

Ash (White)

Tough and elastic, sapwood pale milky white, heartwood ranging from light brown to dark brown. Wood grain is obvious, coarse grain. Simple processing, easy to bend with steam method. Use luxury furniture, flooring, moldings, fine woodworking products, sports equipment, tool handles and so on.

Ash wood

Tough and elastic, milky white or pinkish. The processing is simple and it is easy to bend with the steam method, but it is apt to decay, so it is not easy to use for appearance.

Fireproof board

Fire board is made of silicon or calcium material as the main raw material, and a certain proportion of fiber materials, lightweight aggregates, adhesives and chemical additives mixed by autoclave technology made of decorative plates. It is a new type of material that is being used more and more. Its use is not only due to fire protection. The construction of the fire board requires a relatively high requirement for glue sticking, and the fire board with better quality is also more expensive than the decorative panel. Fire board thickness is generally 0.8mm, 1mm and 1.2mm.

Core board

The big core board is a kind of special sandwich plywood, which is made of wood strips with the same thickness and different lengths and arranged in close splicing. It is generally a five-layer structure. The vertical core plate (differentiated by the direction of the core material) has poor flexural compressive strength, but the transverse flexural compression strength is high.

Decorative panel

Decorative panels commonly known as panels. It is a veneer with a thickness of about 0.2mm, and a veneer with a single-sided decorative effect. It is a special way of plywood, with a thickness of 3%. Decorative panels are currently an advanced decoration material that is different from the oil mixing practice.

Splint

Also called plywood, three or more layers of one-millimeter-thick veneer or sheet glue are hot-pressed. With light material, high strength, good elasticity and toughness, impact resistance and vibration, easy processing and finishing, insulation and other advantages.

Peach Wood

The sapwood is grayish brown and the core material is grayish brown.

Tochigi

Sapwood yellow and white, dark gray core material.

Three-layer particleboard

The surface layer is made of thinner, smaller, special mini shavings, and the core layer is made of thicker, larger rough shavings. Three paving heads are used.

Particle Board (Flakeboard)

Particle board, also known as particle board, is dried glue (such as wood shavings, flax, bagasse, etc.) made of wood shavings made of wood or non-wood plants that have been filled with rubber and auxiliary materials or have not been given rubber and auxiliary materials. Hot pressed sheet.

Particle board is classified as follows:

1, according to use points: divided into Class A particle board and B particle board;

2. According to the structure of the particle board: a. single-layer particle board; b. three-layer structure particle board; c. gradual structure particle board; d. oriented particle board; e. waffle particle board; f. molded particle board;

3, according to surface conditions: unfaced particle board: a. sanding particle board; b. not sanding particle board. Finishing chipboard: a. impregnated paper facing particleboard; b. decorative laminate facing particleboard; c. veneer facing particleboard; d. surface finishing particleboard; e. PVC decoration?

4, according to the use of raw materials points: a. wood chipboard; b. bagasse particleboard; c. linen chipboard; d. cotton stalk particle board; e. bamboo particle board, etc.; f. cement particleboard; g. plaster particle board;

5, according to manufacturing methods: a. flat pressure particleboard; b. extruded particle board.

birch

It grows in the northern hemisphere and has a shiny surface and a smooth mechanism. It is white, with a slightly pink ivory or grayish-yellow wood heart. It is not very durable in an easily decaying environment and is used in more splint form. Now used for the production of structures, parquets and internal frames.

Melamine board

The melamine board full name is a melamine impregnated paper film facing panel. The paper is made of melamine resin adhesive soaked in paper with different colors or textures, and then dried to a certain degree of curing, and it is paved on the surface of particleboard, medium-density fiberboard or hardboard, and the hot-pressed decorative board.

MDF

MDF is also called fiberboard. The artificial board made of urea-formaldehyde resin or other suitable adhesives based on wood fiber or other plant fibers is classified into high-density board, medium-density board, and low-density board depending on its density. MDF is also easy to rework because of its soft and impact resistance. In foreign countries, MDF is a good material for making furniture, but due to the fact that the national standard for height plates is several times lower than international standards, the quality of use of MDF in China needs to be improved.

Blockboard

Blockboard line commonly known as Daxinban. Daxin board is made of two pieces of veneer and pressed and spliced ​​with wood. The vertical core plate (differentiated by the direction of the core material) has poor flexural compressive strength, but the transverse flexural compression strength is high.

Real wood

Solid wood is the raw material, mainly refers to the rules made of logs and logs. Commonly used logs include Chinese fir, red pine, Chinese ash, ash, camphor, eucalyptus, and more valuable are rosewood, eucalyptus, oak and so on.

Huang Huamu

The sapwood is light yellow and the core material is brownish.

Ash

The sapwood is light brown and the core material is light brown, but slightly darker than the sapwood.

Willow

Sapwood gray, brown core material.

Tochigi

Sapwood yellowish brown, dark gray core material.

Korean pine

The sapwood is light yellow and the core material is yellowish red.

【 Font: Large   in   small   】

Bai Song

The color difference between the sapwood and the core material is white or light yellow.

PVC lattice board

The raw material is first calendered into a flat sheet, and the sheet is deformed by pressing the sheet using a vacuum forming method. This plate has a variety of three-dimensional square and rectangular grid, which is characterized by the rigidity of the plate, can absorb the stretching deformation of PVC, the unique effect of the facade, the production and installation are easy. The specifications are generally 500mm x 500mm and the thickness is 2 to 3mm.

PVC plastic board

PVC is an abbreviation of polyvinyl chloride resin, and polyvinyl chloride is a linear thermoplastic polymer. With PVC as the base material, add plasticizers, stabilizers, pigments, fillers, lubricants, etc. At a certain temperature, kneading, mixing, pulling, pelletizing, extruding, or die-casting molding can be made into plastic products after cooling and setting.

Light steel keel gypsum board ceiling

The combination of gypsum board and light steel keel forms a light steel keel gypsum board. Light steel keel gypsum board ceiling paper gypsum board, decorative gypsum board, fiber gypsum board, hollow gypsum board variety. From the current point of view, the use of light steel keel plaster ceilings is more of a partition wall, but less used to make smallpox.

Mirror stainless steel decorative panel

Stainless steel sheet is specially polished. Its characteristics are as bright as a mirror surface, reflectivity, deformation rate and high-level mirror almost the same, and fire-resistant, moisture-resistant, no deformation, no broken, easy installation, but should be hard material scratches.

Color coated steel plate

It is made of hot-rolled steel plate and galvanized steel plate coated with 0.4-0.5mm soft or semi-rigid polyvinyl chloride plastic film. It has heat and corrosion resistance and can be used as wallboard.

Calcium plastic decorative board

Calcium-plastic decorative board, also known as calcium plastic foam decorative sound-absorbing board, is divided into general board and non-flammable board. This kind of decorative board is made of polyethylene resin added with inorganic fillers. It has a variety of concave and convex patterns or perforation patterns on the surface. It has the characteristics of light weight, heat preservation, sound absorption, heat insulation, insect resistance, water resistance, and small deformation, and it is beautiful in appearance. The construction is convenient, but its durability and aging resistance are slightly inferior.

Aluminum plate

Aluminum buckle plate with a light aluminum stamping molding, the outer layer and then spray paint with a special process, long-term use does not fade, the construction is relatively simple, not easy to deformation, fire, moisture, anti-static, sound-absorbing and sound insulation, and beautiful and practical. There are two punching and flat surfaces on the surface of the aluminum pinch.

PVC corrugated board

Also known as PVC corrugated board, a longitudinal corrugated board; its width is 900 to 1300mm, the length is not limited, for transport convenience is generally the longest 5000 to 6000mm; the other is a transverse corrugated board, its width is 800 Up to 1500mm, the amplitude of the transverse corrugated plate is small and can be placed in a roll. The length of each roll is 10 to 30m. There are also some unique waveforms for the PVC corrugated plate, such as broken lines and arcs.

Splint smallpox

Plywood (also called plywood) has the advantages of light material, high strength, good elasticity and toughness, impact resistance and vibration resistance, easy processing and painting, and insulation. It can also easily create a variety of modeling ceilings such as curved, round, square, etc., but the disadvantage is that they are afraid of termites.

Plasterboard ceiling

The gypsum ceiling is made of plaster of Paris as the main raw material and is blended with additives and fibers. It has properties such as light weight, heat insulation, sound absorption, flame retardance, and sawability. Multi-use and commercial space science, generally using 600 * 600 specifications, with the distinction between bone and dark bone, keel commonly used aluminum or iron.

Aluminum alloy decorative plate

It is also called aluminum alloy pressure plate or ceiling buckle plate. It is made of aluminum and aluminum alloy as raw materials. It is processed by roll pressing and cold pressing into various sections of metal plate. It has light weight, high strength, good rigidity, corrosion resistance and long-lasting. Durable and other excellent performance. After the surface of the board has been anodized or painted and sprayed, a variety of colors required for decoration can be formed.

Plasterboard

It uses gypsum as the main material, adding fibers, adhesives, and modifiers, and mixing and pressing to dry them. With fire protection, sound insulation, heat insulation, light weight, high strength, low shrinkage and other characteristics and good stability, no aging, pest control, available nails, saws, planing, sticking and other methods of construction. Widely used in ceilings, partitions, interior walls, and plywood. Gypsum board is divided into ordinary paper gypsum board, fiber gypsum board, gypsum board 3 kinds.

Plaster ceiling

The main raw material of cooked gypsum is blended with additives and fibers to make it lighter, heat-insulating, sound-absorbing, flame retardant, and sawable.

PVC board

With PVC as raw material, it can be waterproof, moisture-proof and anti-mite, and it contains flame-retardant raw materials.

Tiles Buying Board Three Trees Lacquer Decorating Furniture Aluminum Alloy Stainless Plasterboard Ceiling Ceiling Price Decoration White Furniture

Textile Ceramic

Textile Ceramic,Ceramic Tools ,Ceramic Materials ,Ceramic Supplies

Inorganic Pigment Co., Ltd. , http://www.nbceramicpipe.com